Top 10 common forklift accidents ， forklift operation need to take notice of these matters ！.

Don't undervalue the forklift at the workplace. If the procedure is not good, there will be serious mishaps in mins, and there are numerous mishaps including forklifts.

Instance 1: The forklift freight blocked the driver's sight, and the person in front might not be discovered, leading to a moving accident.
Case 2: In order to maintain the balance of the forklift when lifting hefty items, the employees used their body weight as the weight, which almost caused casualties.
Case 3: The width of the forklift cargo goes beyond the allowed size of the route and holds on the roadside rack, which almost causes an mishap.
Situation 4: Forklift is speeding up and surrender throughout a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift raises the personnel unlawfully, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Case 7: The forklift chauffeur did not wear a safety belt and fell from the car when it surrendered and was squashed.
Forklift operation must pay attention to these issues ：.

Beginning.
1. Before beginning, observe the environments, and after verifying that there are no challenges that impede the safety of driving, honk the horn first and after that begin.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge have to be risk-free prior to starting.
3. When the forklift starts with a lots, the motorist needs to first confirm that the tons is steady and reputable.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole ought to be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork must not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork must be decreased to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal ought to be released initially. High-speed sharp turns are banned. High-speed doglegs will create the vehicle to lose side stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the fire and slide, and it is restricted to brake instantly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it needs to follow the web traffic rules in the manufacturing facility and need to keep a certain security distance from the automobile in front. .
7. When the forklift is running, the load needs to remain in the lowest setting that does not hinder the driving, and the gantry ought to be correctly tilted back. The lots will not be increased except when piling or loading. .
8. The height of the tons need to not block the vehicle driver's sight. In special situations, when the item influences the forward vision, drive at a low speed when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a balancing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and unloading.
1. When fork-loading things, the distance in between both forks ought to be readjusted as required to make the load of the two forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the automobile should be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch other products or things. The load must be maintained with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit easy placement of the tons and removal of the forks. .
6. It is forbidden to fork products at high speed and collide with hard things with the fork head. .
7. When the forklift is working, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Straining is banned, and it is prohibited to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special scenarios, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look needs to be examined, and gas, lubricating oil and cooling water should be included.
2. Examine the safety and security efficiency of starting, running and braking.
3. Inspect whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send out a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass Stand-on Electric Pallet Stacker 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Running up and down the incline should be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the gradient. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and other dangerous chemicals with Stand-on Electric Pallet Stacker forks.
5. It is not allowed to utilize inertia force to grab the goods.
6. It is not enabled to use braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to deal with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is raised.
8. Do not drive side to side on inclines
.
Car parking is not permitted under the list below conditions.
1. Contours, slim roadways, train crossings;.
2. Sections with a longitudinal slope more than 5%.
3. When there is an obstacle on one side of the roadway, the contrary side of the section with the exact same length as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844